How to Administer TB Tests

Tuberculosis (TB) is a bacterial infection. It is spread through saliva droplets emitted when an infected person coughs or sneezes. TB is a global health issue, and is potentially fatal if left untreated. The Purified Protein Derivative (PPD) TB Skin Test, also known as the Mantoux Test, was developed to test for active and latent TB. The test is carried out by a health practitioner. If your TB test result is positive, treatment for TB will follow if deemed necessary.

Things You'll Need

• Warm water
• Soap
• Towel
• Latex gloves
• Well-lit room
• Firm surface
• Alcohol wipe
• Vial of tuberculin
• Single-use disposable tuberculin syringe
• Puncture-resistant disposable container
• Cotton balls
• TB test record form
• Appointment card
• Caliper ruler

Show More

Instructions

• 1

  Wash your hands with warm water and soap to remove any dirt or bacteria, and dry them with a towel. Put on clean latex gloves.

• 2

  Choose a well-lit area to administer the test, and have all of the necessary equipment to hand before you begin.

• 3

  Ask your patient to remove his jacket and roll up his sleeve to reveal his forearm. Place the patient's arm on a firm surface.

• 4

  Ask the patient to extend his arm, with his palm facing upward and his elbow slightly flexed.

• 5

  Select an area approximately two to four inches from the elbow toward the hand. The area must be free of tattoos, cuts, bruises and any other imperfections.

• 6

  Clean the area using an alcohol wipe, then leave to air-dry for one minute.

• 7

  Puncture the vial with the needle, and then pull back the plunger to release the tuberculin.

  Fill the syringe with the tuberculin by puncturing the tuberculin vial with the needle at the top of the syringe. Then slowly pull the plunger at the opposite end of the syringe, withdrawing the liquid via the needle until the syringe is full.

• 8

  Remove the needle from the empty vial and hold it upward toward the ceiling. Gentle tap the syringe with your finger to allow any air bubbles to rise to the top.

• 9

  Push the plunger very gently to remove any air bubbles and excess tuberculin, leaving exactly 0.1 milliliter in the syringe, as indicated by the measurement on the side of the syringe.

• 10

  Hold the syringe with your thumb and index finger as you would hold a pen, and position the syringe at a five to 15 degree angle to the patient's arm so the tuberculin will enter just below the surface of the skin.

• 11

  Inject the tuberculin slowly. It should form a six to 10 millimeter wheal, a pale, raised area with round edges that resembles an insect bite and does not disappear immediately. Repeat the test on the opposite arm if a wheal does not appear.

• 12

  Remove the needle and discard of it immediately in the puncture-resistant container.

• 13

  Dab the injection area with a cotton pad if bleeding occurs, but do not apply pressure to the site or cover it with an adhesive bandage because this could cause irritation.

• 14

  Wash your hands and record the details of the test including the location of the test (left or right arm), the tuberculin lot number and expiration date (these details are found on the tuberculin vial), date and time the test was administered and your signature.

• 15

  Inform the patient that he must return within 48 to 72 hours to have the test result read, and make him an appointment to do so.

• 16

  Examine the injection site upon the patient's return 48 to 72 hours later, using a caliper ruler to measure any swelling. According to the National Library of Medicine Medline Plus, an area of firm swelling greater than 15 millimeters in size indicates that the TB test is positive. For people considered at risk of contracting TB, such as those with HIV or diabetes, the amount of swelling needed to indicate a positive result is reduced to around five to 10 millimeters.